Just how to Install a Bathtub ( Guide).

Book

Just how do you really feel when it comes to Installing A Bathtub?


How to Install a Bathtub
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, carpentry, and in some cases, tiling abilities. Changing an old bathtub with a brand-new one is additionally a moderately challenging job. If the old bathtub is readily available, the job can relocate speedily; if you have to open a wall surface to get rid of the old tub as well as place the brand-new bath tub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will need a helper to vacate the old bathtub and also embeded in the new one. Ensure you have actually qualified yourself for the task as well as fit trying it. As opposed to hiring a professional to take over a halfway-completed job, it is much better to take into consideration using one prior to you start. Chances are you may need a professional plumber to make tube connections.
This short article will assist you set up a brand-new tub in your shower room if you have actually currently gotten a brand-new bathtub as well as do not require to alter the plan of your previous water system pipes.
Your tools as well as material checklist ought to make up the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps


  • Removing Old Touches


    If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The process of removing the existing faucets can be fairly bothersome because of the restricted access that is often the case.
    Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will certainly originate from the pipes. Once the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
    Prior to carrying on to fit the new faucets, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.

    Suitable New Touches


    If the tails of the new faucets are plastic, then you will require a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap as well as the other end gives a connection to the existent supply pipelines.
    If you need to fit a monobloc, after that you will call for reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
    Next off, place the tap in the installing hole in the bath/basin making sure that the washers remain in place in between the tap and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous type needs to be connected to the faucet ends initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.

    Mounting the Bathtub


    Making use of the two wooden boards under its feet, position the bathtub in the called for position. The wooden boards are handy in evenly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little factors.
    The next objective is to make certain that the bathtub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bathtub up until the level reads level.
    To set up faucets, fit the bottom of the furthest adaptable faucet connector to the appropriate supply pipe by making a compression sign up with; after that do the same for the other tap.
    Activate the supply of water and also examine all joints and new pipework for leakages and also tighten them if necessary. Fill the tub as well as additionally check the overflow outlet as well as the typical electrical outlet for leakages.
    Finally, fix the bath paneling as explained in the maker's user's manual. Tiling and sealing around the bathtub ought to wait up until the tub has actually been made use of at the very least once as this will settle it into its final setting.

    Getting ready for the Installment


    To start with, the sustaining structure provided with the bath should be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to ensure that if the tap includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to stop pressure on the bath tub.
    Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you use all of the supplied washing machines.
    Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be suited its final position.

    Tiling Around the Bathtub


    In the location where the bath meets the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the installation can move sufficient to split a stiff seal, causing the water to pass through the wall between the bathroom and the tiling, bring about issues with dampness and also feasible leaks to the ceiling listed below.
    You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are sold in tubes as well as cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill up the bath tub with water before securing, to enable the activity experienced when the tub remains in usage. The sealant can fracture relatively very early if you do not take into consideration this movement prior to sealing.
    Additionally, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly available on the market. It is suggested to fit the ceramic tiles making use of water-resistant or water-proof adhesive as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    Do you appreciate reading about How to Install a Bathtub? Place feedback down the page. We'd be glad to listen to your opinion about this piece. Hoping to see you back again in the near future. You should set aside a second to distribute this blog entry if you enjoyed reading it. I thank you for reading our article about A Step-by-Step Guide to Installing a Bathtub.



    Click Here To Find Out More

    Leave a Reply

    Your email address will not be published. Required fields are marked *